Accessories

The Light Traffic Channel Grate shown is a vehicular grate designed for passenger vehicles and light trucks. Other grates and sizes are also available.

Each hub outlet allows you to use 3- and 4-inch corrugated pipe or sewer and drain pipe. To extend the height of the catch basin, use a piece of 6-inch SDR-35 PVC pipe. Each catch basin comes with universal outlet inserts.

The grate fits inside the top of the box to make a 12" x 12" receptacle area. The extension makes the catch basin six inches deeper. Multiple extensions may be stacked to increase the height.

Each hub outlet allows you to use 3- and 4-inch corrugated pipe or sewer and drain pipe. Multiple extensions may be stacked to increase the height. Each catch basin comes with universal outlet inserts.

Used on flared end sections with 3:1 slopes to help keep debris out and prevent clogging.

Used on flared end sections with 3:1 slopes to help keep debris out and prevent clogging.

Used on projects where 3:1 slope is specified. Fits contour and assists water flow through the culvert.

Used where 6:1 slopes are required. Available with or without safety grate.

For larger sizes (5"-15"), use a blind tee.

Used in layouts requiring a lateral connection. Has three ends, all the same size.

End is blind (solid). Also used as a 90º elbow. Cut blind end for a straight tee. Reducing stub: 8"-10" and 12".

Gives you a down-size selection. Reducing stub for stepping down.

A combination tee that can be used on 3- and 4-inch pipe. The lugs on the inside and outside are similar to our internal couplers.

A special fitting for layouts requiring a 45º connection.

A one-step reducer. Easily goes up or down.

Four-foot square sheet of high density plastic fastened with stainless steel bolts.

Snaps inside the pipe to cap the end.

Caps the end of pipe when required.

External cap to plug the end of pipe when required.

Snaps on easily inside the ends of corrugated pipe to give you a solid connection. Ideal for repair work.

Snaps on the exterior of corrugated pipe to give you a solid connection. Ideal for repair work.

The split makes this coupler easy to open and wrap around the outside of the pipe. Use tape or plastic ties to join.

Provides a good connection between corrugated pipe and clay, concrete or PVC.

For use when attaching corrugated pipe to rectangular downspout.

An end cap or end plug with a 4-inch hole drilled off-center to allow the maximum amount of effluent to enter the system.

Provides a soild tight connection between corrugated pipe and clay, concrete or PVC.

For use when attaching corrugated pipe to rectangular downspout.

An end cap or end plug with a 4-inch hole drilled off-center.

*Special order item

*Special order item

The Light Traffic Channel Grate shown is a vehicular grate designed for passenger vehicles and light trucks. Other grates and sizes are also available.

Child-proof, rugged self-locking safety lid.Fits - Sump.

For radon abatement systems. Child-proof, rugged self-locking lid (solid) is drilled for gasketed piping and venting. Includes gaskets.

Prinsco’s water collection basin is intended for use with a sump pump. The built-in outer extensions feature self-locking inlets for easy installation. Saw off the end and snap 4-inch tubing in place. Capacity: 11 gallons to inlet and 21 gallons to lid.

Our 6-inch locking sump extensions are designed to be stacked for adjustable depths. It’s easy to install because it snaps into place the same way the locking lid does. The added height of the sump unit gives contractors a method of lowering the sump inlets for easy installation. It also allows the installer a simple and cost-effective way to increase the size of the sump basin.

The grate fits inside the top of the box to make a 12" x 12" receptacle area. The extension makes the catch basin six inches deeper. Multiple extensions may be stacked to increase the height.

Each hub outlet allows you to use 3- and 4-inch corrugated pipe or sewer and drain pipe. To extend the height of the catch basin, use a piece of 6-inch SDR-35 PVC pipe. Each catch basin comes with universal outlet inserts.

Each hub outlet allows you to use 3- and 4-inch corrugated pipe or sewer and drain pipe. Multiple extensions may be stacked to increase the height. Each catch basin comes with universal outlet inserts.

2 ox. Typar - Flat Roll Sheets (Sold per roll)

For larger sizes (5"-15"), use a blind tee.

Used in layouts requiring a lateral connection. Has three ends, all the same size.

End is blind (solid). Also used as a 90º elbow. Cut blind end for a straight tee. Reducing stub: 8"-10" and 12".

Gives you a down-size selection. Reducing stub for stepping down.

A combination tee that can be used on 3- and 4-inch pipe. The lugs on the inside and outside are similar to our internal couplers.

A special fitting for layouts requiring a 45º connection.

A one-step reducer. Easily goes up or down.